全国统一服务热线: 13567769200
产品中心
  • JCC1-95

JCC1-95

所属分类:绝缘穿刺线夹

服务热线:13567769200

联系传真:

邮箱留言:32396157@qq.com

公司地址:乐清市柳市象阳工业区

打印当前页面

绝缘穿刺线夹(Insulation Piercing Connectors)主要由绝缘壳体、穿刺刀片、防水胶垫、力矩螺栓组成。当做电缆分支连接时,将分支电缆插入支线帽并确定好主线分支位置后,用套筒扳手拧紧线夹上的力矩螺母,随着力矩螺母的拧紧,线夹上下两块暗藏有穿刺刀片的绝缘体逐渐合拢,同时,包裹在穿刺刀片周围的弧形密封胶垫逐步紧贴电缆绝缘层,穿刺刀片亦开始穿刺电缆绝缘层及金属导体。当密封胶垫和绝缘油脂的密封程度和穿刺刀片与金属体的接触达到最佳效果时,力矩螺母自动脱落,此时,安装完成且接触点密封和电气效果达到最佳。
The Insulation Piercing Connectors is mainly composed of an insulating shell, a piercing blade, a waterproof rubber pad and a torque bolt. As a branch of cable connection, the branch cable is inserted into the cap and confirm the main branch line position, the torque nut with the socket wrench, tighten the clamp with tightening torque nut, clamp down two pieces of a puncture blade insulator gradually closed, at the same time, wrapped in a curved blade gradually around the puncture sealing pad close to the cable insulation layer, the puncture blade also began to layer and a metal conductor insulation puncture cable. When the sealing degree of the sealant pad and the insulation grease reaches the best effect when the contact between the puncture blade and the metal body reaches the best effect, the torque nut automatically falls off. At this time, the installation is completed, and the contact point seal and the electric effect reach the best.
安装简便 不需剥去电缆的绝缘皮即可做电缆分支,接头完全绝缘。不需截断主电缆,可在电缆任意位置做分支。安装简便可靠,只需用套筒扳手,可带电安装
使用安全 接头耐扭曲、防震、防水、阻燃、防电化腐蚀老化,无需维护,已成功使用30多年
节约成本 安装空间极小,节省桥架和土建费用。建筑中应用,不需要终端箱、分接箱,不需电缆返线,节省电缆投资。电缆+穿刺线夹的费用低于其他供电系统,仅为插接母线的40%左右,是预制分支电缆的60%左右
穿刺结构,安装简单,绝缘导线无需剥皮;
力矩螺母,穿刺压力恒定,确保良好的电气连接而不损伤导线
电气接触电阻小,接触电阻小于等长分支导线电阻的1.1倍,符合DL/T765.1-2001标准
特殊绝缘壳体,抗光照及环境老化,介电强度>1KV
弧面设计,适用同(异)径导线连接,连接范围广(0.75mm2-400mm2)
型号Specification JCC1-95
电压电流Voltage 1KV,75A
主线截面Main line 16-95mm2
支线截面Branch line 1.5-10mm2
压线螺丝Screw M6
力矩Torque 9N·m
外观尺寸Dimension 27*41*62mm
路灯照明系统(竖井禁用)
建筑照明、路灯、高层竖井线连接
高层建筑竖井电缆户外架空线
电缆沟工厂动力供电主缆
注:①适用穿刺线夹的到导线必须符合国家标准; ②穿刺线夹的安装人员必须完全掌握安装技术;
③在带电作业时,请带上绝缘手套筒扳手; ④穿刺线夹属于一次性线夹,由于牙型变形拆卸后请勿重复使用。
将线缆放入线夹的正确位置后用手拧紧
Put the cable into the correct position of
the clip and tighten it with the hand
用六角套筒均匀拧紧力矩螺母
Tighten the torque nut evenly with the wrench tool
直至拧断力矩螺母,完成安装
Until the wring moment nuts, to complete the installation
穿刺结构,安装简单,绝缘导线无需剥皮;
特殊绝缘壳体,抗光照及环境老化,介电强度>1KV
力矩螺母,穿刺压力恒定,确保良好的电气连接而不损伤导线

宝杰

  • 关注微信

  • 进入阿里旺铺

13567769200

版权所有 @ 2018 浙江宝杰电力科技有限公司 | 全国免费服务热线:13567769200